Lawn Mower Maintenance

Mowing the lawn is an enjoyable task, but it can also be a very time-consuming one. It’s important to keep your grass mower maintained so that it lasts a long time and performs well during use. The following steps will help you maintain your mower. If you need any lawn maintenance or landscaping, send us a message for a free quote!

Lawn Mower Maintenance

Check the oil level.

Check the oil level.

Checking the oil level is the first step in keeping your lawn mower running smoothly. Maintaining a consistent level of oil in your machine will ensure that it starts up quickly and doesn’t stall out when you need it most—like when cutting grass for a large family or yard party! To check for an adequate supply of fuel, simply pull off a small amount of the plastic cap and run your finger along its edge until you reach an area where there’s no more liquid visible (this should take about 1/4 inch). The ideal amount is between 1/8th and 3/16ths full; if you find yourself having trouble finding this mark, then add more fuel until you do.

How often should I check my lawnmower’s oil?

Checking this part of your mower can help prevent problems like clogged filters or worn out drive belts—and it only takes a few minutes each week! If possible, try to schedule weekly maintenance so that it won’t interfere with other activities during peak season (such as planting seeds).

Check the air filter.

Check the air filter.

The air filter is located on top of your lawn mower, near the engine. It’s important to check this regularly in order to keep your mower running smoothly and efficiently. If you have any dirt, debris or other foreign objects in it, remove them with a screwdriver or something similar until you can see clearly through the holes in the housing that holds it in place. Then look for clogging—this could be caused by leaves falling onto an old lawnmower blade; if there are no leaves remaining on top of your blade, but there are still clumps underneath it (especially if they’ve been there for a while), these may be causing slow-moving parts like belts and pulleys to wear out faster than normal due to increased friction from repeated use over time as well as other reasons not yet known by me!

Check the spark plug and replace it if necessary.

• Check the spark plug for carbon deposits, wear and a loose connection.
• If you’re not getting consistent performance from your mower, it’s time to adjust your spark plug gap by using a feeler gauge or other tool of your choice (i.e., feeler gage). You can find directions for doing this in your owner’s manual or online at www.machinerydepotonline.com/how-to-adjust-valves/how-to-adjust-a-spark-plug

Inspect the blade and sharpen it if necessary.

• Inspect the blade and sharpen it if necessary.
• Look for cracks or wear on the blade. If you see any, replace it!
• If you don’t have a sharpener, use a file to make your own.

Clean the deck and blade.

• Clean the deck and blade. Use a nonabrasive cleaner to remove any dirt, grime or grass buildup on your lawn mower’s deck and blades. If you’re using a brush instead of spray cleaners, be sure to use one that is not abrasive because it can damage these parts of your machine.
• Wipe down with damp rags as necessary until clean (or dry).

Adjust your mower’s height.

Adjust your mower’s height. To adjust the height, you’ll want to take off the gas tank cover and pull down on springs located on either side of this cover. Once these are removed, you can then adjust your mower’s height manually by raising or lowering it by turning a screw located inside this area (see photo). Alternatively, you may use a lever instead of manually adjusting this feature—just make sure that when doing so, you’re not cutting off too much fuel so as not to damage any parts underneath!

With this knowledge, you should be able to take care of your lawn mower and make sure it reaches its full potential. Remember that oil is a vital part of any machine and should always be checked for any signs of leakage or contamination before use. You can also adjust the height of your mower by removing the wheels from the underside and adjusting them up or down with an Allen wrench if necessary!